Skip to content
Service procedures

SOC Reset

Gen3/tasks/PROC_HVBMS_X_RESET-SOC

Model 3 / YModel S / X (2021+)

What this task does

Resets all HV battery brick State of Charge (SOC) values based on the latest Open Circuit Voltage (OCV) brick measurements. During normal operation, the HVBMS ECU calculates brick SOCs from multiple data sources. This routine should be executed when the SOC is >90% or <15% and the HV battery has rested (not charging, driving, or climate ON) for at least one hour within that SOC range.

Vehicle compatibility

Select your vehicle’s hardware to see task details, requirements, and inputs. Availability is confirmed after connection.

Model 3 / Y AMD
Vehicle coverage
2024+ Model 3, 2025+ Model Y, Model Y, Pre-2024 Model 3
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Factory, DiagLinkActive, Service

Procedure notes

The displayed miles/percentage on the vehicle display might update to match the current OCV brick measurements. Pack contactors will open and then close shortly after.

Task inputs (0)

This task has no listed user inputs.

Model 3 / Y Intel
Vehicle coverage
Model Y, Pre-2024 Model 3
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Factory, DiagLinkActive, Service

Procedure notes

The displayed miles/percentage on the vehicle display might update to match the current OCV brick measurements. Pack contactors will open and then close shortly after.

Task inputs (0)

This task has no listed user inputs.

Model S / X (2021+) AMD
Vehicle coverage
2021+ Model S, 2021+ Model X
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Factory, DiagLinkActive, Service

Procedure notes

The displayed miles/percentage on the vehicle display might update to match the current OCV brick measurements. Pack contactors will open and then close shortly after.

Task inputs (0)

This task has no listed user inputs.

Related service tasks

Browse all tasks →
Service procedures

Blocked Contactors - Attempt to Clear

Clears open Voltage Sensing Harness (VSH) latch alerts and isolation counters. Resets the High Voltage Processor (HVP) and High Voltage Battery Management System (HVBMS) Electronic Control Units (ECU) in an attempt to clear blocked contactors. Even in the case all internal routines PASS, contactors may still be blocked from closing due to other external conditions.

PROC_HVBMS_X_CLEAR-BLOCKED-CONTACTORS

Model 3 / Y Model S / X (2021+)
Service procedures

Clear HVBMS Open VSH Latch

Clears the Voltage Sense harness (VSH) alert BMS_a119_Fast_Open_Vsh_Detected latch within the HVBMS NVRAM. This routine shall only be executed after installing a new/remanufactured HV battery.

PROC_HVBMS_X_RESET-VSH-FAULT

Model 3 / Y Model S / X (2021+)
Service procedures

HVBMS - Clear Isolation Counters

This routine clears the High Voltage Battery Management System (HVBMS) isolation counters, which clears BMS_a027_SW_Repeated_Isolation_Failure_In_Drive and BMS_a172_SW_Isolation_Failure_In_Drive_Warning alerts. Execute this routine after repairing any isolation issue on the vehicle's High Voltage (HV) system. The HVBMS isolation counters latch the alerts BMS_a027 and BMS_a172 when reaching a certain count threshold.

PROC_HVBMS_X_RESET-ISOLATION-COUNTERS

Model 3 / Y Model S / X (2021+)
Self-tests

HVBMS BMB and VSH Connection Test

This routine checks the HVBMS connections to the Battery Monitoring Board (BMB) and the Voltage Sense Harness (VSH).

TEST-SELF_HVBMS_X_BMB-COMMS-VSH

Model 3 / Y Model S / X (2021+)