TPMS UDS ECU Reset
The test resets the Tire Pressure Monitoring System (TPMS) ECU via UDS.
TEST-RESET_TPMS
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
1,357 tasks Showing 1249–1272
Browse by name, A–Z
The test resets the Tire Pressure Monitoring System (TPMS) ECU via UDS.
TEST-RESET_TPMS
Tests whether the Trailer Light Controller (TLC) load is connected to the left vehicle controller (VCLEFT) ECU.
TEST_VCLEFT-TLC_REAR_TRAILER-CONTROLLER-CONNECTED
Tests whether the trailer light controller (TLC) load is disconnected from VCLEFT.
TEST_VCLEFT-TLC_REAR_TRAILER-CONTROLLER-DISCONNECTED
Tests communication of the Trailer Light Controller (TLC) Electronic Control Unit (ECU). Communication is established over the Local Interconnect Network (LIN) bus network.
TEST_VCLEFT-TLC_REAR_TRAILER-LIN-COMM
Runs all required routines after a Tesla Restraints Control Module (TRCM) replacement and arms the system.
PROC_TRCM_X_SERVICE-TASKS
Checks communication with the Tesla Restraints Control Module (TRCM). Communication is established through Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_TRCM
The procedure triggers an Odin Patch installation if a patch is available for the vehicle's installed firmware signature.
PROC_ICE_X_INSTALL-PATCH
Triggers an Odin Patch uninstall to fall back to installed firmware
PROC_ICE_X_UNINSTALL-PATCH
ODIN checks with the ECU if a log upload is available. If it is, ODIN downloads the data and uploads it to garage logs.
PROC_ODIN_X_TRIGGER-ECU-LOG-UPLOAD
Tests for power, connection, and communication of the left trunk interior illumination controlled by the Left Vehicle Controller (VCLEFT).
TEST-SELF_VCLEFT_X_TRUNK-INTERIOR-LIGHT
Tests for power, connection, and communication of the right trunk interior illumination controlled by the Right Vehicle Controller (VCRIGHT).
TEST-SELF_VCRIGHT_X_TRUNK-INTERIOR-LIGHT
Tune radio by inputting BAND (AM/FM/DAB/XM) and FREQUENCY (station). PLEASE HAVE RADIO PANEL PULLED UP ON THE UI BEFORE RUNNING.
PROC_ICE_X_TUNE-RADIO
Tuner and Antenna Connection Check
TEST-BASH_CID_X_TUNER-ANTENNA-ALL
Perform a tuner and antenna connection check.
TEST-BASH_CID_X_TUNER-ANTENNA
Based on vehicle configuration, corresponding option of tuner is checked.
TEST-BASH_CID_X_TUNER-ANTENNA-ALL
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-APAC-BASE
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-APAC-PREMIUM
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-EU
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-NA-BASE
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-NA-PREMIUM
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-ROW
Turns off an individual e-fuse power feed for the selected component. The channel powers down respecting the going-down timer. When the timeout expires, power is restored automatically.
PROC_VC_X_POWER-OFF-REQUEST
Turn on the accessory (ACC) power rail.
PROC_CID_X_ACC-RAIL-ON
Turn on the interior cabin map lights.
PROC_ICE_X_MAP-LIGHTS-ON