Service procedures
Clear IDB DTCs
Clear the Mando Decoupled Brake (IDB) Diagnostic Trouble Codes (DTC).
PROC-IDB_X_CLEAR_DTCS
Model 3 / Y
Clear DTCs
Common/tasks/PROC_X_CLEAR-DTCS
What this task does
Clears the diagnostic data on the chosen Electronic Control Unit (ECU). This will clear any active Diagnostic Trouble Codes (DTC). DTC functionality may not exist on all ECUs depending on the platform.
Vehicle compatibility
Select your vehicle’s hardware to see task details, requirements, and inputs. Availability is confirmed after connection.
Model 3 / Y AMD
- Vehicle coverage
- 2024+ Model 3, 2025+ Model Y, Model Y, Pre-2024 Model 3
- Supported connection
- Local connection
- Vehicle state
- Stationary · Parked
- Gateway diagnostic level
- Factory, DiagLinkActive, Service, Park
Task inputs (3)
ECU
ecu_name · EnumType
The ECU to clear the diagnostic data for
Default: ALL
Options: ALL, TESLA, THIRD_PARTY, BMS, CP, DI, DIF, DIR, DIREL, DIRER, DIRE1L, DIRE1R, DIRE2, HVBATT, HVBATT1, HVBATT2, HVBATT3, PCS, PCSL, PCSR, PEBS, PPB, SEBS, VCFRONT, VCFRONT2, VCLEFTS3, VCRIGHTS1, VCSUPER
DTC Group
dtc_group · EnumType
The DTC group to input into the clear command (0xFFFF33 for CARB, 0xFFFFFF for all)
Default: FFFFFF
Options: FFFFFF, FFFF33
Set Power
set_power · Bool
Whether to set the vehicle power state
Default: false
Model 3 / Y Intel
- Vehicle coverage
- Model Y, Pre-2024 Model 3
- Supported connection
- Local connection
- Vehicle state
- Stationary · Parked
- Gateway diagnostic level
- Factory, DiagLinkActive, Service, Park
Task inputs (3)
ECU
ecu_name · EnumType
The ECU to clear the diagnostic data for
Default: ALL
Options: ALL, TESLA, THIRD_PARTY, BMS, CP, DI, DIF, DIR, DIREL, DIRER, DIRE1L, DIRE1R, DIRE2, HVBATT, HVBATT1, HVBATT2, HVBATT3, PCS, PCSL, PCSR, PEBS, PPB, SEBS, VCFRONT, VCFRONT2, VCLEFTS3, VCRIGHTS1, VCSUPER
DTC Group
dtc_group · EnumType
The DTC group to input into the clear command (0xFFFF33 for CARB, 0xFFFFFF for all)
Default: FFFFFF
Options: FFFFFF, FFFF33
Set Power
set_power · Bool
Whether to set the vehicle power state
Default: false
Model S / X (2021+) AMD
- Vehicle coverage
- 2021+ Model S, 2021+ Model X
- Supported connection
- Local connection
- Vehicle state
- Stationary · Parked
- Gateway diagnostic level
- Factory, DiagLinkActive, Service, Park
Task inputs (3)
ECU
ecu_name · EnumType
The ECU to clear the diagnostic data for
Default: ALL
Options: ALL, TESLA, THIRD_PARTY, BMS, CP, DI, DIF, DIR, DIREL, DIRER, DIRE1L, DIRE1R, DIRE2, HVBATT, HVBATT1, HVBATT2, HVBATT3, PCS, PCSL, PCSR, VCFRONT, VCFRONT2, VCLEFTS3, VCRIGHTS1, VCSUPER
DTC Group
dtc_group · EnumType
The DTC group to input into the clear command (0xFFFF33 for CARB, 0xFFFFFF for all)
Default: FFFFFF
Options: FFFFFF, FFFF33
Set Power
set_power · Bool
Whether to set the vehicle power state
Default: false
Related service tasks
Browse all tasks →
Service procedures
Clear RCU DTCs
Clear the Mando Redundant HCU (RCU) Diagnostic Trouble Codes (DTC).
PROC-RCU_X_CLEAR_DTCS
Model 3 / Y
Service procedures
Clear Side View Mirror Fold Type
Executes a routine to clear the side view mirror fold actuator type auto-detected by the Tesla ECU.
PROC_X_CLEAR-MIRROR-FOLD-TYPE
Model 3 / Y
Service procedures
Compressor RPM Override
Set the compressor to a target speed (800-7000 RPM). If sweep is disabled, the compressor will ramp to target RPM and hold that speed for 15 seconds. If sweep is enabled, the compressor will ramp to target RPM in 500 RPM increments and hold at final target RPM for 15 seconds. Note: The routine may skip some RPM values during sweep, or stop short of the target RPM. This is because some vehicles have certain speeds that are avoided.
PROC_X_COMPRESSOR-RPM-OVERRIDE
Model 3 / Y
Model S / X (2021+)