Skip to content

Tesla service tasks.

Find the procedure. Understand what it does. Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.

1,357

service tasks

Model 3, Y, S & X

Find a service task

665 tasks Showing 121–144

Clear filters
Service procedures

Clear Side View Mirror Fold Type

Executes a routine to clear the side view mirror fold actuator type auto-detected by the Tesla ECU.

PROC_X_CLEAR-MIRROR-FOLD-TYPE

Model 3 / Y
Service procedures

Clear Spotify Cache

The procedure clears the Spotify cache to free up disk space.

PROC_ICE_X_CLEAR-SPOTIFY-CACHE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Clear Spotify Credentials

The procedure clears existing Spotify credentials.

PROC_ICE_X_CLEAR-SPOTIFY-CREDS

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Clear Steering Wheel Haptic Calibration Flag

Clears the stored steering wheel haptic motor calibration flag, forcing the system to recalibrate. Use this routine after replacing the steering wheel or haptic motor.

PROC_VCLEFT_X_CLEAR-HAPTIC-CALIBRATION

Model S / X (2021+)
Service procedures

Clear Updater Backups

The procedure clears all updater backups from the Infotainment and Connectivity ECU (ICE). This Task will only run if the filesystem has run out of inodes, otherwise it will cancel.

PROC_ICE_X_CLEAR-UPDATER-BACKUPS

Model 3 / Y Model S / X (2021+)
Service procedures

Clear Updater Backups

The procedure clears all updater backups from the Infotainment and Connectivity ECU (ICE). This Task will only run if the filesystem has run out of inodes, otherwise it will cancel.

PROC_ICE_X_CLEAR-UPDATER-BACKUPS

Model S / X (legacy)
Service procedures

Collect and Upload ICE and/or APE Log Files to Garage

Collects log files from the ICE (Gateway) or APE/APEB (Autopilot) based on specified log paths, then uploads the results to Garage for analysis and/or ticket creation.

PROC_ICE_X_HERMES-GRABLOGS-V2

Model 3 / Y
Service procedures

Compressor RPM Override

Set the compressor to a target speed (800-7000 RPM). If sweep is disabled, the compressor will ramp to target RPM and hold that speed for 15 seconds. If sweep is enabled, the compressor will ramp to target RPM in 500 RPM increments and hold at final target RPM for 15 seconds. Note: The routine may skip some RPM values during sweep, or stop short of the target RPM. This is because some vehicles have certain speeds that are avoided.

PROC_X_COMPRESSOR-RPM-OVERRIDE

Model 3 / Y Model S / X (2021+)
Service procedures

Configure Charger as Master

Configures connected charger as Master. Script Designed to work together with PROC_CHG_X_CHARGER-STATUS Works only with Gen1 and Gen2 chargers. Before performing configuration; -Enter service mode and perform GTW unlock procedure.

PROC_CHG_X_CHARGER-CONFIG-SET-MASTER

Model S / X (legacy)
Service procedures

Configure Charger as Slave

Configures connected charger as Slave. Script Designed to work together with PROC_CHG_X_CHARGER-STATUS Works only with Gen1 and Gen2 chargers. Before performing configuration; -Enter service mode and perform GTW unlock procedure.

PROC_CHG_X_CHARGER-CONFIG-SET-SLAVE

Model S / X (legacy)
Service procedures

Configure modem ECall

Configure modem ECall for LE940B6-RW Telit modems.

PROC_LTE-MODEM_ECALL-CFG

Model 3 / Y
Service procedures

Configure Pedestrian Warning Speaker (PWS)

Used during a PWS retrofit. Sets the pedestrian warning speaker to either SPEAKER or EXT_SPEAKER_V2, depending on the vehicle platform.

PROC_ICE_X_SET-PEDESTRIAN-WARNING-SPEAKER-CONFIG

Model 3 / Y Model S / X (2021+)
Service procedures

Configure Rear Oil Pump LIN Node ID

This routine is used specifically in Model S with a front permanent magnet drive unit, and the rear Small Drive Unit (SDU) has an electricaloil pump. This routine configures the rear oil pump after installation. ONLY the rear pump is required to be connected, and the oil pump installed into the front drive unit shall remain disconnected, in order for the routine to be run successfully.

PROC_PMS_REAR_WRITE-OPC-TYPE

Model S / X (legacy)
Service procedures

Continental Air Suspension Leveling

Levels the Continental Air Suspension to the selected target height. Low = 3, Standard = 4, High = 5, Very High = 6.

PROC_EAS_X_LEVEL-TO-HEIGHT

Model S / X (legacy)
Service procedures

Continental Service Drive Alignment

This routine will perform a Service Drive Alignment for Continental Radars to check vertical calibration. Before starting the routine, make sure Gateway is unlocked and Drive-rail is turned on. Follow on screen instructions.

PROC_RADC_X_CONTINENTAL-SERVICE-DRIVE-ALIGNMENT

Model S / X (legacy)
Service procedures

Coolant - Start Thermal Fluid Fill and Drain

Starts the Thermal Fluid Fill and Thermal Fluid Drain procedures. Returns result when routine is started, but runs for up to 50 minutes.

PROC_VCFRONT2_X_START-THERMAL-FILL-DRAIN-COOLANT

Model 3 / Y
Service procedures

Coolant Air Purge

Powers the accessory rail and runs HVAC pumps at maximum speed, changing the valve positions. Estimated time to complete is 20 minutes. To exit the routine early, run this routine again with STOP as the input.

PROC_THC_X_COOLANT-AIR-PURGE

Model S / X (legacy)
Service procedures

DAS - Capture Image

Performs an image capture while the Autopilot Electronic Control Unit (ECU) is in Calibration Mode. The estimated time to complete is two minutes.

PROC_DAS_X_CAPTURE-IMAGE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

DAS - Clear Camera Calibration

Clears the Driver's Assistance System (DAS) calibration data for select camera pairs or all cameras.

PROC_DAS_X_CLEAR-CALIBRATION

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

DAS - Clear Lens Hood Alert

Clears the lens hood occlusion alert from the camera health system.

PROC_DAS_X_CLEAR-LENS-HOOD-ALERT

Model 3 / Y Model S / X (2021+)